Oil Canning in Metal Wall Cladding: What Causes It and When Should It Be Investigated?

Large metal wall panels can look smooth from one position and slightly wavy from another. The effect may become more visible when sunlight moves across the wall, when the viewing angle changes or when the panel temperature rises during the day. 

This visual waviness is known as oil canning. It is associated with the flatter areas of light-gauge metal panels and can occur even when the cladding continues to perform as intended. The useful question for a builder, architect or property manager is whether the appearance is a normal characteristic of the selected system or whether other signs point to an installation, support or movement issue. 

For projects where a smooth architectural finish is important, oil canning should be considered during profile selection, detailing and metal cladding installation rather than after the wall is complete. 

What oil canning actually looks like 

Oil canning appears as shallow ripples or waves across the flatter zones of a metal panel. It is usually easier to see on broad flat pans than on strongly corrugated or deeply ribbed profiles because there is more uninterrupted surface for light to reflect across. 

The appearance can change during the day without the panel itself developing a new defect. Low-angle sunlight can exaggerate small surface variations, while diffuse light can make the same wall look considerably flatter. Viewing distance and the direction from which the wall is seen can change the effect as well. 

For that reason, a single photograph taken in strong side light is useful evidence of appearance, but it is not enough on its own to establish that the cladding has failed. 

Why oil canning can develop 

Oil canning does not usually come from one isolated cause. The final appearance can reflect the panel profile, stresses within the sheet, the condition of the supporting plane, fixing pressure, handling and normal temperature movement. 

Panel shape and flat width 

Profiles with wide flat areas tend to show surface variation more readily than profiles with frequent ribs or corrugations. This is mainly a visual effect: broad surfaces make small changes in flatness easier for the eye to detect. 

The selected profile therefore influences appearance expectations before the first sheet reaches site. A design that prioritises long, smooth wall planes should allow for the fact that light-gauge metal will not necessarily read like a perfectly rigid flat plate. 

The fixing plane and fastening pressure 

Wall sheets follow the structure or secondary framing to which they are fixed. If girts, battens or other supports create high and low points, broad panels can be pulled across those irregularities and make the waviness more visible. 

Fastening can also influence appearance. Uneven or excessive pressure at fixing points can introduce local stress into the sheet. Correct fixing therefore depends on the specified cladding system, support spacing and installation method rather than a generic approach applied to every panel type. 

Forming, transport and handling 

Metal sheet already contains residual stresses from coil processing and profile forming. Long panels can then pick up additional stress if they are twisted, point-loaded or poorly supported during transport and lifting. 

Handling damage is not always obvious while sheets are stacked. Once the panels are fixed across a large wall, minor distortion can become much easier to see because adjacent sheets create a continuous visual plane. 

Temperature movement 

Metal expands and contracts as its temperature changes. Queensland walls exposed to direct sun can experience much higher surface temperatures than the surrounding air, followed by cooling later in the day. 

A cladding system needs to accommodate the movement anticipated by its design. If movement is unnecessarily restrained, stresses can become more visible in the flat areas of the panel. Temperature can also change how existing waviness looks from hour to hour. 

Colour and finish influence visibility 

Colour and surface finish affect how readily oil canning is noticed. Darker finishes can experience greater solar heating, while glossy surfaces create stronger reflections that reveal shallow waves more clearly. Lower-gloss finishes can make the same degree of surface variation less obvious. 

This does not make a dark or smooth architectural finish unsuitable. It means visual expectations should be discussed before the cladding profile, colour and finish are finalised, especially on highly visible elevations. 

How to reduce avoidable visual distortion before installation 

Oil canning cannot always be eliminated from light-gauge metal cladding, but several project decisions can reduce avoidable distortion. These decisions are most effective before installation begins. 

Select a profile whose flat-pan width suits the required architectural appearance. 

Confirm that the supporting plane is straight and suitable for the specified cladding system. 

Use the fixing method and spacing required for the selected profile and project design. 

Allow for the movement expected in the panel system rather than restraining sheets unnecessarily. 

Support long panels correctly during storage, lifting and installation. 

Review colour, gloss and prominent viewing angles where appearance is a major design consideration. 

These controls improve the quality of the installed facade, but they should not be presented as a promise that every light-gauge panel will appear perfectly flat under every lighting condition. 

When visible waviness deserves closer assessment 

Oil canning by itself does not prove that a wall is structurally unsound or allowing water into the building. Closer assessment becomes more useful when the visual waviness appears together with another symptom. 

Panels are pulled sharply around individual fixing points. 

Joints or panel edges no longer align as intended. 

Sheets are loose, creased or visibly damaged. 

The supporting wall plane appears irregular or has moved. 

Water ingress is occurring in the same area. 

Coatings are damaged around distorted sections. 

The appearance changed after later building work or impact damage. 

Those symptoms should be investigated for their own cause. A wall can show oil canning without those problems, and a genuine fixing or water-entry defect should not be dismissed simply because oil canning is also visible. 

A practical way to review an existing wall 

Before deciding that panels need replacement, document the pattern. Photograph the same elevation from a consistent position at different times of day. Note whether the waviness changes with light and temperature or remains concentrated around the same fixings, joints or support lines. 

For a recently completed project, keep the cladding profile, panel orientation, colour, support layout and fixing information available for the review. Where a localised area looks different from the rest of the wall, compare it with surrounding panels rather than judging the entire facade from one isolated reflection. 

This approach helps distinguish a general visual characteristic of the panel system from a local condition that may require adjustment or further investigation. 

Plan the appearance before the wall is installed 

Oil canning is easier to manage during design, procurement and installation than after a completed wall becomes an appearance concern. Profile geometry, support condition, fixing details, colour, finish and panel handling all influence what the finished wall looks like. 

Envy Roofing provides metal cladding installation for commercial, industrial and residential projects across Brisbane, the Sunshine Coast and Gold Coast. For larger facilities where cladding interfaces with a broader roof and building-envelope scope, see Envy Roofing’s industrial roofing services. 

Builders, architects and property managers can contact Envy Roofing to discuss a new cladding project or an existing wall that needs assessment. 

Subscribe to our News, Tips and

a selection of our best Projects