Why Metal Wall Cladding Leaks: Common Causes and What to Check

Water ingress behind metal wall cladding often begins at joints, flashings or openings rather than through the metal sheets themselves. A wall may appear intact from outside while rainwater is travelling behind the cladding and reaching the building’s internal structure. 

For commercial property owners, builders and facility managers, finding the source of a leak is important before deciding whether repairs or replacement work are required. Water appearing inside a building may result from a localised installation defect, deteriorated components or a problem with how different parts of the external wall connect. 

Understanding how these problems develop can help prevent repeated repairs and unnecessary damage. 

This guide focuses primarily on profiled metal sheet cladding, commonly used on commercial, industrial and residential buildings. Other systems, including insulated sandwich panels and proprietary architectural cladding, may require different weatherproofing arrangements. 

How Does Water Get Behind Metal Wall Cladding? 

Metal cladding is designed to shed rainwater away from the building. Under ordinary conditions, most rainfall travels down the outside of the sheets. Water ingress becomes more likely where this continuous surface is interrupted by a joint, penetration or connection to another building element. 

Wind-driven rain creates additional challenges. Strong winds can push water towards exposed joints and flashings, including areas that remain dry during lighter rainfall. 

Pressure differences between the exterior and the space behind the cladding can force water through inadequately protected openings. Water can also move through narrow gaps by capillary action, particularly where overlapping metal surfaces are closely spaced. 

These mechanisms help explain why some cladding leaks occur only during storms, even when the wall appears to perform adequately during ordinary rainfall. 

A properly designed wall assembly must account for these conditions. Depending on the system, protection may involve correctly configured sheet laps, flashings, compatible seals, membranes and provisions for drainage and drying. 

The Australian Steel Institute’s guidance on steel wall cladding explains how these components contribute to weather resistance and moisture management. 

Five Common Causes of Water Ingress in Metal Wall Cladding 

1. Incorrect Sheet Laps and Joint Installation 

Profiled metal sheets are connected through overlapping edges or interlocking joints, depending on the selected cladding product. 

These joints must be installed according to the manufacturer’s specifications. Their performance depends on the profile geometry, orientation, fixing arrangement and exposure to weather. 

Vertical cladding generally encourages rainwater to travel down the length of the sheets. Horizontal cladding requires particular attention to the arrangement of overlaps and flashings, especially where the profiles intersect windows, doors and corners. 

Some horizontal installations require additional detailing to prevent wind-driven rain from passing behind the sheets. 

Problems may develop when adjacent sheets are incorrectly aligned, laps do not engage as intended or the installation does not follow the requirements of the selected profile. 

Movement, damaged fixings and sheet distortion can also affect previously sound joints. 

A visible gap is not always the only problem. Water may enter through an incorrectly configured overlap even when the surrounding sheets appear undamaged. 

Repairing the joint therefore requires an understanding of how the profile is intended to manage water, rather than simply covering the exposed opening with sealant. 

2. Poorly Installed Flashings Around Windows and Doors 

Windows and doors introduce multiple junctions into a metal-clad wall. These openings require careful detailing because water travelling down the cladding must be redirected around the frame and discharged outside. 

The head flashing helps manage water arriving from above the opening. Jamb details protect the vertical connections, while the sill flashing must allow water to discharge away from the assembly. 

The effectiveness of these components depends on how they connect to one another, the surrounding cladding and any secondary weatherproofing layers. 

For example, a head flashing may be correctly shaped but still allow water ingress if its upper edge is positioned incorrectly relative to the cladding or membrane. 

Similarly, poorly coordinated sill and jamb details can allow collected water to reach the surrounding wall construction. 

The resulting moisture may become visible around the internal window reveal, below the sill or farther along the wall. 

Because water can travel across concealed components before reaching an internal surface, the visible damage does not necessarily identify the original point of entry. 

Where a window begins leaking after cladding replacement or other building modifications, the investigation should include the interfaces disturbed during that work. 

3. Defective Roof-to-Wall Junctions and Parapet Flashings 

Commercial and industrial buildings frequently have sections where a lower roof meets a higher metal-clad wall. 

These areas require coordination between the roof covering, wall cladding and the flashings connecting them. 

Rainwater travelling down the wall must be directed onto the appropriate external drainage surface. At the same time, the junction must resist wind-driven rain and prevent water from passing behind the cladding. 

Apron flashings commonly form part of these details. Their effectiveness depends on the required cover, fixing, sealing arrangements and position relative to the adjoining materials. 

Parapet walls create further exposure because water may reach their upper surfaces, cappings and adjoining roof connections. 

Poorly formed cappings, inadequate overlaps or unsuitable junction details can allow water to enter the construction below. 

The Queensland Building and Construction Commission identifies inadequate roof flashing construction, including parapet and apron flashings, as a significant cause of water penetration. 

These problems can also develop after the original installation. Roof replacement, extensions or alterations to mechanical plant may require existing flashings to be removed or modified. 

If the replacement components are not properly integrated with the existing wall cladding, the junction may become vulnerable to water ingress. 

For buildings requiring both metal wall cladding and commercial roofing installation, coordinating the two systems during project planning can help avoid incompatible or incomplete weatherproofing details. 

4. Poorly Sealed Penetrations and Inappropriate Fixings 

External walls often contain penetrations for electrical conduits, ventilation systems, mechanical services and other building equipment. 

Each penetration interrupts the cladding surface and needs a weatherproofing detail appropriate to its size, position and expected exposure. 

A penetration may require a proprietary flashing, collar, seal or another manufacturer-approved arrangement. The selected detail must remain effective under normal building movement and weather conditions. 

Fixings can also contribute to water ingress. 

On exposed-fix cladding systems, unsuitable fasteners, damaged sealing washers or incorrect installation can compromise the weather resistance around fixing points. 

Fasteners that are overdriven, incorrectly positioned or incompatible with the surrounding materials may also affect the performance of the installation. 

Commercial buildings are particularly vulnerable to problems introduced during later modifications. 

New signage, service installations and equipment upgrades may require additional penetrations through an existing wall. These changes can disturb flashings, membranes or other components that were originally installed as part of a coordinated system. 

Where water ingress appears after work by another trade, the affected penetrations and connections should be included in the investigation. 

5. Blocked or Incorrectly Detailed Drainage Paths 

Not every metal cladding system is designed to prevent all moisture from passing beyond the outermost sheet under every exposure condition. 

Some systems incorporate secondary protection that allows incidental water to drain away without damaging the structure. 

This may involve membranes, underflashings, cavities or other drainage provisions, depending on the wall assembly. 

Where a drainage cavity is part of the design, water entering that space must be able to reach an appropriate outlet. The arrangement should also support drying where required. 

Problems can occur when lower wall terminations obstruct drainage, when debris accumulates around an outlet or when later construction changes the original discharge path. 

Landscaping, paving and building extensions can sometimes interfere with the space provided beneath cladding. 

Applying sealant across a designed drainage opening can create another problem. Although it may appear to prevent water from escaping, it can retain moisture within the assembly. 

An obstruction that prevents incidental water from draining may allow moisture to accumulate around structural framing, insulation or other vulnerable components. 

The required termination detail depends on the specific cladding system. Openings and clearances must not be added or altered without checking the relevant design and manufacturer instructions. 

Is Moisture Behind Metal Wall Cladding Always Caused by Rainwater? 

Not all moisture found behind metal wall cladding originates from an external leak. 

Condensation can produce similar symptoms, particularly when humid air reaches surfaces that are cold enough for water vapour to condense. 

This can occur within concealed parts of the wall, including areas around framing, insulation and internal linings. 

In Queensland, the risk deserves particular consideration in air-conditioned buildings. 

During warm, humid conditions, outdoor air can carry significant moisture. If that air enters the wall assembly and encounters surfaces cooled by the building’s air-conditioning system, condensation may develop. 

The risk depends on the wall construction, temperature differences, air leakage, humidity and the arrangement of insulation and vapour-control layers. 

Condensation and rainwater penetration require different investigations. Replacing external cladding or resealing visible joints may not resolve a moisture problem caused by inappropriate vapour control or air leakage. 

The Australian Government’s YourHome guidance on condensation explains how climate, insulation, ventilation and building membranes influence moisture accumulation. 

A professional assessment may be required to distinguish between these causes, particularly when the affected area is concealed or moisture appears without a consistent relationship to rainfall. 

What Should Property Managers Check Before Arranging Cladding Repairs? 

When water appears inside a building, the first step is to document the problem and identify any patterns that may assist a professional investigation. 

The timing of the leak can provide useful information. Moisture that appears during strong winds and heavy rain may indicate exposure-related water ingress, while persistent dampness under different conditions may require a broader investigation. 

Neither observation establishes the cause on its own. 

Property managers can record where staining or moisture becomes visible, whether the problem is recurring and which areas of the building are affected. 

Photographs taken safely from ground level or other accessible locations can help document visible damage, including displaced flashings, loose sheets, deteriorated sealants or changes around openings. 

Existing construction drawings, product documentation and maintenance records may also be useful. They can help identify the installed cladding profile, intended weatherproofing details and previous alterations. 

Recent work deserves particular attention. If water ingress begins after a roof replacement, service installation or external building modification, the affected junctions should be reviewed. 

The condition of internal materials should also be considered. Damp plasterboard, damaged insulation, corrosion and persistent moisture may indicate that water has been present for longer than the visible staining suggests. 

Inspection work involving access at height, removal of cladding or concealed electrical services must be carried out with appropriate professional expertise and safety controls. 

Once the source has been established, the required work can be assessed against the condition of the existing system. 

A localised defect may be addressed without replacing an entire wall. More extensive deterioration or unsuitable original construction may require a broader solution. 

How Correct Metal Cladding Installation Reduces Water Ingress Risks 

Long-term weather resistance depends on the design and installation of the complete wall system, not simply the durability of the metal sheets. 

Cladding profiles must be appropriate for the building and its environmental exposure. Flashings, fixings, membranes and connections to other building elements must be compatible with the selected system. 

In South East Queensland, wind-driven rain is a relevant design consideration, while coastal projects may require additional attention to corrosion resistance and material compatibility. 

The correct specification depends on the site’s exposure, the building’s wind design requirements and the materials involved. 

For profiled sheet metal cladding, AS 1562.1:2018 provides requirements for the design and installation of systems within its scope. 

The National Construction Code references AS 1562.1 as a Deemed-to-Satisfy compliance pathway for relevant metal wall cladding applications. The applicable requirements and available compliance pathways depend on factors including the building classification and approved design. 

Manufacturer installation instructions remain important because cladding profiles can have different requirements for laps, fixing locations, supporting structures and flashings. 

The QBCC’s guidance on roof flashings also reinforces the importance of effective flashing arrangements that intercept and discharge water without relying excessively on sealants. 

Sealants have legitimate applications where specified as part of a suitable system. They should complement correctly designed joints and flashings rather than compensate for unsuitable construction. 

Installation planning should also account for the work of other trades. 

Window placement, roof connections, service penetrations and drainage terminations need to be coordinated before the wall is completed. Resolving these details during construction helps reduce the likelihood of concealed defects and disruptive corrective work later. 

Planning Metal Wall Cladding Installation or Replacement in Queensland? 

Metal wall cladding provides a durable external finish, but its weatherproofing performance relies on correct material selection and careful installation around joints, openings and building connections. 

Envy Roofing provides metal cladding installation for commercial, industrial and residential properties across Brisbane, the Sunshine Coast and Gold Coast. 

The team works with builders, architects and property managers on new cladding installations and upgrades to existing building exteriors. 

If you’re planning a new project or considering replacement of existing metal wall cladding, contact Envy Roofing to discuss your building requirements. 

Call 1300 213 430 or email info@envyroofing.com.au. 

Subscribe to our News, Tips and

a selection of our best Projects